Item Code: MR192

Finally, an versatile Compact Fluorescent ballast for the DIY aquarist! This solid state electronic ballast has advanced Raid Start technology built into it.

* ARO brand PC ballast, will power up to 192W (2x 96W), but can fire any combination of 2x 55W, 2x 65W or 2x 96W!
* Parallel connection allows you to operate only 1 lamp if desired! If 1 lamp burns out, the other one will continue to run. However, both lamps will turn on/off at the same time.
* Will fire 96W quad lamps.
* Add additional supplemental lighting to your aquarium, or upgrade to power compact lighting.
* Highly efficient electronic ballast, no annoying hum like other magnetic ballasts.
* Small compact design.
* Wiring diagram on the ballast.
* Model #MR-192 raw ballast only, endcaps, powercord and lamps sold separately.
* You can wire these directly to our CF endcaps, or extend them with 18G wire and wire nuts (not provided) if you want to extend the wires.
Note: For maximum longevity and safety, wire ballast away from heat or humidity sources.

* Warranty: 1 Year

Warning: To avoid damage to your system, make sure the lamp(s) are seated firmly in their endcap(s). Any lamp not fully pushed into their endcap can result in an ARC, potentially causing damage/failure to your system. If you are not sure how to properly install the lamp, please call us toll free at 866-969-7333 or 866-WOW-REEF. Damage caused by an arc is not covered under warranty.

* Caution: This ballast kit must be housed in an area free of moisture, behind glass or acrylic. Make sure the bulb(s) and socket(s) are sealed off from any moisture, humidity or evaporation of your aquarium. Failure to do so will void any and all warranty, and could be a potential hazard.

ARO MR-192 Ballast Specs
Maximum Power: 192 Watts
Maximum Current: 1.60 AMP (120vac)
Operating Voltage: 120 VAC ± 10%
Black, White Wires: 18" Long From Case
Red, Blue, Yellow, Brown Wires: 18" Long From Case
Ballast Case Size: Long Case - 9 3/4"L x 1 5/8"W x 1 1/8"H
Ballast Weight: 18.5 OZ
High Power Factor: > .90
Ballast Min. Operating Temp.: -20° F (-30º C)
Ballast Maximum case Temp. : 158º F (70º C)
Ballast Lamp Starting Mode: Raid Start (better than Instant Start for the bulbs)
Class P (Thermal) Sound Rating - A
End of Life Protection: No EOL Circuit

FAQ:
Q. Can I run 28W and 36W lamps on this? I saw another raw ballast on another site, and it claims to 'run anything'.
A. Well, don't let all the mis-information out there confuse you. This ballast will "run" all those lamps in the question above, however, it's not recommended for 2x 28W or 2x 36W due to performance degradation. Sure, the MR-192 will light those lamps, but you will not the performance out the lights that you think you are getting. Remember, if it claims to "do it all", be wary. With lighting, you should use the proper ballasts to drive the lamps they were designed for, if you want the best possible performance for your aquarium.
Q. How would I run only 1 lamp on this ballast?
A. Just wire up 1 lamp per the wiring diagram, and safely cap off the wires for the other lamp using wire nuts. This would allow you to run a single lamp.
Q. Why are the wires coming out of the ballast silver, are they aluminum?
A. No. The wires coming out of the ballast are copper coated with tin (like solder). Although they are silver in color, they are not aluminum, but rather solid copper covered with tin.

Hellolights highly reccomends the use of a ground fault circut interrupter with all of the lighting equipment we offer. With the correct installation and proper precautions taken you can avoid electrical shock or electrocutions.